VDA 355 Module Peak Discharge Current Explained

Short answer: The VDA 355 1P4S module carries a rated discharge current of 174 A, a peak discharge current of 348 A, and a maximum discharge current of 465 A. These three figures are distinct: they describe different operating conditions and durations. Reading them correctly is essential before sizing a pack for a given power requirement.

Current ratings on a battery module datasheet are not interchangeable. Pack engineers who treat peak, continuous and maximum as synonyms risk either over-stressing a module or leaving usable power on the table. This article works through the figures for the VDA 355 1P4S module in detail and shows how those figures translate into pack-level power through a concrete series-string example.

The 1P4S module: base figures

The module used throughout this article is the VDA 355 1P4S configuration. Its catalogue values are:

Parameter Value
Nominal capacity (rated) 174 Ah
Measured capacity 177 Ah
Nominal voltage 14.64 V
Energy content 2.59 kWh
Rated discharge current 174 A
Peak discharge current 348 A
Maximum discharge current 465 A
Maximum continuous discharge current 348 A
Maximum charge current 348 A
Maximum continuous charge current 209 A
C-rate reference 1C

The rated discharge current of 174 A equals the rated capacity of 174 Ah, which is 1C. That relationship is the starting point for every other current figure on the sheet.

Peak, continuous and maximum: three different things

All three terms appear on datasheets, and all three mean something different. Confusing them is one of the more common errors in pack specification.

Rated discharge current (174 A): The continuous current the module is designed to sustain under normal operating conditions, defined at 1C. This is the figure to use as a planning basis for sustained power delivery.

Peak discharge current (348 A): 348 A is the peak figure for this module, equal to 2C. A peak rating applies for a limited duration. The datasheet is the authoritative source for how long that peak may be held: do not assume a duration from the catalogue entry alone. Using the peak figure as though it were a sustained rating will shorten module life and may trigger protection thresholds.

Maximum discharge current (465 A): This is the highest current the module can pass under any condition. It is not a peak in the sense used above. 465 A represents an absolute ceiling, not an operating target. Treat it as the boundary beyond which protection must intervene. Do not describe 465 A as the peak: the peak is 348 A. The two must not be used interchangeably.

Maximum continuous discharge current (348 A): Note that the maximum continuous figure equals the peak figure for this module. That is not always the case across module families. Here it means 348 A is both the highest sustained continuous rating and the peak rating. Confirm this relationship on the datasheet for any module you are sizing.

Maximum charge current (348 A) and maximum continuous charge current (209 A): Charge limits are asymmetric relative to discharge. The maximum continuous charge current of 209 A is notably lower than the 348 A continuous discharge limit. This is intentional: lithium cell chemistry tolerates higher instantaneous discharge rates than charge rates before degradation mechanisms accelerate. Pack power budgets must account for this asymmetry: the available charging power is not the mirror image of discharge power.

For a full treatment of how these figures sit within the broader module specification, see the VDA 355 module datasheet key figures explained page.

Power follows from voltage multiplied by current

Power in a DC system is voltage multiplied by current (P = U x I). To convert module-level current ratings into pack-level power figures, you need the pack voltage, which is set by the number of modules in series.

Worked example: 27 modules in series

Assemble 27 of these 1P4S modules in series. The pack nominal voltage is:

27 x 14.64 V = 395.3 V (approximately 395 V)

That voltage is consistent with a 400 V bus architecture, which is a common target in both automotive and industrial applications. For pack design guidance on series and parallel arrangements, see the VDA 355 battery pack design series and parallel guide.

Apply the three current ratings to that pack voltage:

Rated (1C) discharge power: 174 A x 395 V = 68,730 W, approximately 68.7 kW

Peak discharge power: 348 A x 395 V = 137,460 W, approximately 137 kW

Maximum continuous charge power: 209 A x 395 V = 82,555 W, approximately 82.6 kW

The gap between 137 kW (peak discharge) and 82.6 kW (continuous charge) is not trivial. A regenerative braking event in a vehicle, or a grid-balancing discharge in a stationary application, can demand power that the charge path cannot absorb at the same rate. BMS logic and charge controllers must enforce the 209 A continuous charge ceiling independently of whatever the discharge path permits.

All calculations above use the nominal voltage of 14.64 V per module. Actual pack voltage varies with state of charge and temperature. Sizing to nominal gives a reasonable midpoint; thermal and state-of-charge effects must be modelled separately for a complete power budget.

Why the charge limit is lower than the discharge limit

The asymmetry between maximum continuous discharge (348 A) and maximum continuous charge (209 A) reflects electrochemical constraints at the cell level. During charge, lithium plating on the anode becomes a risk at high current densities, particularly at low temperatures. During discharge, the same current density produces different stress patterns that the cell tolerates more readily. The IEC standard IEC 62619 for safety requirements of secondary lithium cells and batteries used in industrial applications addresses abuse conditions including overcurrent, and charge rate limits are part of the compliance boundary. Always verify that your BMS enforces the charge current limit stated on the module datasheet, not the discharge limit.

Reading the datasheet: what to check

When reviewing a module datasheet for current ratings, confirm the following before using any figure in a design:

  • The duration or duty cycle associated with each rating (rated, peak, maximum) must be stated explicitly on the datasheet. If it is not, ask the supplier before proceeding.
  • The temperature range to which each rating applies. Current limits typically derate at low temperatures.
  • Whether the maximum continuous discharge current and peak discharge current are the same value or different. For this 1P4S module they are both 348 A; that is not universal.
  • The charge limit is separate from the discharge limit and must be treated separately in BMS configuration.

For context on how these figures relate to the broader range of VDA 355 configurations and formats, see the advantages of the VDA 355 format and the VDA 355 module dimensions and specifications pages. The IEA's global battery demand data, published at iea.org, provides market context for understanding why standardised module formats that carry clear current ratings are increasingly important across both vehicle and stationary applications.

Frequently asked questions

What is the peak discharge current of the VDA 355 1P4S module?
The peak discharge current is 348 A, equal to 2C relative to the 174 Ah rated capacity. This figure applies for a limited duration defined on the datasheet. It is not the same as the maximum discharge current of 465 A, which is an absolute ceiling, not an operating target.

What is the difference between peak discharge current and maximum discharge current on a VDA 355 datasheet?
For the 1P4S module, peak discharge is 348 A and maximum discharge is 465 A. The peak is a time-limited high-current operating condition. The maximum is the absolute boundary beyond which protection must intervene. Using the two terms interchangeably leads to incorrect pack sizing.

How do I calculate pack power from VDA 355 module current ratings?
Multiply the module current rating by the pack nominal voltage (P = U x I). For 27 modules in series at 14.64 V per module, pack voltage is approximately 395 V. At 174 A rated discharge that gives approximately 68.7 kW; at 348 A peak discharge approximately 137 kW; at 209 A continuous charge approximately 82.6 kW.

Why is the maximum continuous charge current lower than the maximum continuous discharge current?
For the 1P4S module, continuous charge is limited to 209 A while continuous discharge reaches 348 A. Lithium cells tolerate higher discharge current densities than charge current densities before degradation mechanisms, including lithium plating on the anode, become significant. The BMS must enforce the charge limit independently of the discharge limit.

What C-rate does the rated discharge current of the VDA 355 1P4S module represent?
The rated discharge current of 174 A equals exactly 1C, because the rated capacity is 174 Ah. Peak discharge at 348 A is 2C. The maximum discharge current of 465 A is approximately 2.67C. The datasheet must be consulted for the duration each of these rates may be sustained.

Specify the right module for your power requirement

Review the full range of VDA and MEB battery modules from Avantis Energy with their current ratings, or contact Avantis Energy with a technical question about matching module current limits to your pack power budget.

Next step ยท both links open avantisenergy.eu

Building a pack on VDA 355?

Avantis Energy supplies prismatic LFP and NMC cells and complete VDA-format modules, so you integrate a proven module instead of validating your own. The catalogue lists 24 module types and 20 cell types.

Request a quote from Avantis EnergyTell us configuration, voltage and quantity. No account needed.
View the VDA module range